Firmendetails

  • Changzhou Ruide Drying Engineering Technology Co., Ltd

  •  [Jiangsu,China]
  • Unternehmenstyp:Hersteller
  • Main Mark: Amerikas , Asien , Europa , Nordeuropa , Andere Märkte , Westeuropa
  • Exporteur:71% - 80%
  • Zert:ISO9001
  • Beschreibung:Verdünnte Phase Pneumatische Förderanlage Hersteller Custom,Verdünnte Phase Pneumatische Fördersysteme,Kundenspezifisches verdünntes Phasen-pneumatisches Fördersystem
Anfrage-Korb (0)

Changzhou Ruide Drying Engineering Technology Co., Ltd

Verdünnte Phase Pneumatische Förderanlage Hersteller Custom,Verdünnte Phase Pneumatische Fördersysteme,Kundenspezifisches verdünntes Phasen-pneumatisches Fördersystem

Zuhause > Produkt-Liste > Pneumatic Conveying System > Verdünnte Phase Pneumatisches Fördersystem > Verdünnte Phase pneumatische Fördersystemhersteller Gewohnheit
Produktgruppe
Online Service

Verdünnte Phase pneumatische Fördersystemhersteller Gewohnheit

Aufteilen:  
    Einheitspreis: USD 26500 - 7500 / Set/Sets
    Incoterm: FOB
    Minimum der Bestellmenge: 1 Set/Sets
    Lieferzeit: 30 Tage

Basisinformation

Modell: Dilute phase pneumatic conveying system

Additional Info

Verpakung: Holzkiste

Produktivität: 15sets

Marke: Ruide

Transport: Ocean

Ort Von Zukunft: China

Versorgungsmaterial-Fähigkeit: 2Sets/Month

Zertifikate : ISO9001

Produktbeschreibung

Product range: Dense Phase Systems

Product category: Pneumatic Conveying Series

Product introduction:

It can be with two ways: tank transmission and rotary valve transmission. The former is through compressing the tank to a stated pressure,switching the discharging valve and air knife to distribute materials( they are in the state of a plunger to realize the whole process of transmission. Speed of airflow transmission is much lower, yet fixing this kind of airflow is much higher. Besides, transmitting barometric pressure is also higher. Air or nitrogen is usually used for transmitting with compressor providing power. Its main characteristics are low transmission speed and little influence against quality of material. Rotary valve pneumatic hyperflow is in the way of Dilute Phase positive pressure to transmitting with compressor providing power. This system has much higher pressure, much lower speed of flow, but much heavier transmitting capacity with little influence again materials.

 conveying system

Pneumatic Hyperflow system usually has the following combination:

 

1. Solid-state Dense Phase

It is usually used for single-point feeding materials, long-distance transmission with the materials being fragile and abrasive. It is almost full of materials in type of plunger flow moving forward in the tubing, which is in a low speed and high density way to transmitting materials in the tubing.

 

2. Discontinuous Dense Phase

It is usually used for single-point feeding materials and much longer-distance transmission. It is almost full of materials in type of plunger flow moving forward in the tubing. Those materials have little abrasiveness to the tubing and are invulnerable to breakage. And they are usually transmitted by positive pressure.

 

Positive transmitting system is an energy-saving with high efficiency transmitting way to transmit materials to a long distance by compressed air.

 

Its air supply is compressor air motor.

 conveying system

According to different transmitting materials and layout forms, it is necessary to calculate pneumatic transmission seriously and rigidly.

 

There are several different transmission ways for positive pressure system as follows:

 

1). In the way of Feeding through Star-rotary valve, transmit materials in the tubing into store holder

2) In the way of Feeding through rotary valve, transmit materials in the tubing into store holder.

 

3). combined negative pressure/ positive pressure transmitting system is through negative pressure driving the near multipoint materials into the aggregate bin, and the bin pump set below the aggregate bin transmitting materials into store holder or other receiving points.

 

3. Continuous dense phase

It is the way of Multipoint feeding and single-point discharging. Materials Transmission speed in the tubing is lower than that of suspended state which is suitable for transmitting powder and little granule.




Produktgruppe : Pneumatic Conveying System > Verdünnte Phase Pneumatisches Fördersystem

Produkt-Bild
  • Verdünnte Phase pneumatische Fördersystemhersteller Gewohnheit
  • Verdünnte Phase pneumatische Fördersystemhersteller Gewohnheit
  • Verdünnte Phase pneumatische Fördersystemhersteller Gewohnheit
Mail an Lieferanten
  • *Fach:
  • *Nachrichten:
    Ihre Nachrichten muss zwischen 20-8000 Zeichen sein
Kontakt mit Lieferant?Lieferant
Denis Mr. Denis
Was kann ich für Sie tun?
Chat Jetzt Kontakten mit Lieferant